• Entrainé par: Mélange air-huile
• Vitesse de rotation : 45.000-50.000 tr/mn
• Nombre de jets: 12
• Pression de service: 4 - 5 bar
• Débit volumétrique: 1040 l/min
• Puissance maximaler: 300 W
• Tige d'outil prise en charge Ø: 3 mm, 4 mm, 6 mm
• Arbres disponibles: Ø: 16 mm, 22 mm, 25 mm, ¾"

Haute précision constante

• La queue de l'outil de coupe fait office d'arbre de broche
• Faux-rond dynamique de 4 microns ou moins
• Remplacement aisé des roulements à chaque changement d'outil de coupe 

Transformez efficacement n'importe quelle machine en centre d'usinage ultra-rapide

• Centres de fraisage, centres de tournage, tours de décolletage
• Prolonge la durée de vie de la broche de la machine
• S'adapte aux porte-outils standard pour le changement automatique d'outils
   

• rpm: 45,000-50,000
• Output Power: 300 Watts
• Tool Shank Diameter: 3 mm, 4 mm, 6 mm
• Shaft Diameter: 25 mm
• Air Pressure: 4-5 bar
• Air Flow: 1040 l/min

Catalogue en ligne 

• rpm: 45,000-50,000
• Output Power: 300 Watts
• Tool Shank Diameter: 3 mm, 4 mm, 6 mm
• Shaft Diameter: 16 mm
• Air Pressure: 4-5 bar
• Air Flow: 1040 l/min

Catalogue en ligne 

• rpm: 45,000-50,000
• Output Power: 300 Watts
• Tool Shank Diameter: 3 mm, 4 mm, 6 mm
• Shaft Diameter: 16 mm
• Air Pressure: 4-5 bar
• Air Flow: 1040 l/min

Catalogue en ligne 

• rpm: 45,000-50,000
• Output Power: 300 Watts
• Tool Shank Diameter: 3 mm, 4 mm, 6 mm
• Shaft Diameter: 16 mm
• Air Pressure: 4-5 bar
• Air Flow: 1040 l/min

Catalogue en ligne 

• rpm: 45,000-50,000
• Output Power: 300 Watts
• Tool Shank Diameter: 3 mm, 4 mm, 6 mm
• Shaft Diameter: 22 mm, ¾“
• Air Pressure: 4-5 bar
• Air Flow: 1040 l/min

Catalogue en ligne 

• rpm: 45,000-50,000
• Output Power: 300 Watts
• Tool Shank Diameter: 3 mm, 4 mm, 6 mm
• Shaft Diameter: 16 mm, 3/4”
• Air Pressure: 4-5 bar
• Air Flow: 1040 l/min

Catalogue en ligne 

Replacement Kit

Includes 2 bearings and 1 turbine, which should be replaced each time the tool is changed. The bearings and turbines are not intended for reuse. Each Replacement kit is suitable for the respective tool shank diameter.

Tool Shank Diameter:          3 mm, 4 mm, 6 mm

Catalogue en ligne 

Bearing Puller

If the tool shank diameter is on the lower end of the manufacturing tolerance, it is possible that the rear bearing may not come out of the housing with the tool during a tool change. In this case, use the Bearing Puller to easily slide the bearing out from the housing.

Catalogue en ligne 

Assembly Device

Used to assemble the bearings and turbine onto the tool shank. The assembly device works with any of the three supported metric tool shank diameters.

Tool Shank Diameter:          3 mm, 4 mm, 6 mm

Catalogue en ligne 

Service unit for compressed air

Consists of a pressure regulator and lubricator and is used to add an oil mist to the compressed air and adjust the air pressure. CoolSpeed® mini Air should not be operated without oil mist.

A service unit can be found online or from your local supplier.

Master Gauge

Used for high accuracy angular alignment of CoolSpeed® mini V Air.

Catalogue en ligne 

All components needed to set up and use CoolSpeed® mini Air. The products are packed in a handy carrying case.

Includes:

CoolSpeed® mini Air

CM-SRK-030 Replacement Kit Ø3 mm

CM-SRK-040 Replacement Kit Ø4 mm

CM-SRK-060 Replacement Kit Ø6 mm

CM-SMD-346 Assembly Device

CM-SBW-001 Bearing Puller

Single open-end Wrench 24 mm

Request Quotation